When a buyer asks a supplier "how much oil can this press make?" the honest answer is "it depends." A screw oil press has a nameplate capacity in kg/h or tonnes per 24 hours, but the real throughput on your floor depends on the seed you feed it, how it is prepared, and how hard you squeeze the cake. Ordering a press that is too small leaves you short on output; ordering one too big wastes capital, power, and floor space on a machine that runs half-empty. The job is to match the model to your actual seed, your daily operating hours, and the residual-oil target you need to make the plant profitable.
How Model Numbers Translate To Tonnage
Most Chinese screw presses are sold under two common naming systems - YZYX and 6YL - where the number is roughly the diameter of the pressing screw in millimeters. As a rough guide, the YZYX70 handles about 1.3 tonnes per day with a 4 kW motor; the YZYX90 about 3 t/day at 5.5 kW; the YZYX120 about 6.5 t/day at 11–15 kW; the YZYX130 about 8–10 t/day at 15–18.5 kW; and the YZYX140 about 9–11 t/day at 18.5 kW. The 6YL family runs in parallel: 6YL-80 around 2–3 t/day, 6YL-95 around 3–5 t/day, 6YL-120 around 200–300 kg/h, and 6YL-160 up to 450–600 kg/h. Think of the model number as a size class, not a fixed number: the same YZYX130 will run faster on free-flowing rapeseed and slower on dense, moist soybeans.
Your Oilseed Decides Real Capacity
The rated capacity on the data sheet is almost always quoted on rapeseed, the industry's reference seed. Feed a different seed and the number changes. Soybean is harder and lower in oil (about 15–20%), so the same press may drop from 8 t/day on rapeseed to 7 t/day on soybean, and the oil yield efficiency sits lower (around 67%) even though the residual oil in cake looks similar. Peanut kernels are high in oil (40–50%) and flow well, so throughput stays near the rating and oil yield efficiency reaches 90%+. Cottonseed and sunflower sit in between. Always ask the supplier to quote capacity on your seed, under your preparation conditions, not on rapeseed - a press that is "8 t/day" may only deliver 5 t/day on your soybeans.
Residual Oil In Cake vs Throughput
There is a real trade-off between squeezing hard and running fast. Closing the choke to push residual oil in dry cake down from 8% to 6–7% recovers more oil per tonne, but it also slows throughput and increases motor load. For most edible-oil plants, a residual oil of 7–8% in peanut and rapeseed cake is the practical balance; soybean cake can be held lower because the starting oil content is already low. If you sell the cake as animal feed, a lower residual oil also improves its protein value and selling price - which often pays for the slower run. Ask the supplier for the residual-oil guarantee on your seed, and whether two-stage pressing is available when you need the extra yield.
Hot Press, Cold Press And Two-Stage Press
Most commercial presses run hot pressing: the seed is cooked in a roaster or cooker to 110–130°C before pressing, which ruptures oil cells and frees the oil, giving higher throughput and lower residual oil. Cold pressing - no cooking - preserves a more "natural" oil flavor but cuts throughput by 20–40% and leaves more oil in the cake, so you need a larger machine for the same oil output. Two-stage (pre-press + final press) presses first at low pressure to recover bulk oil, then at higher pressure for the last few percent; they are used for high-oil seeds like peanut and sunflower and for large plants. Decide which product you are selling - commodity bulk oil vs. premium cold-pressed oil - before you size the press.
Matching Auxiliary Equipment
The press is only one machine in the line. A realistic 24-hour output depends on the seed preparation feeding it: a cleaning/screening step, a cooker or roaster (for hot press), a screw conveyor or bucket elevator to feed the press steadily, and an oil filter (air-pressure or vacuum) to clarify the pressed oil before it goes to storage. Undersized feed or filtration is the most common reason a rated 8 t/day press actually delivers 5 t/day. Tell the supplier your whole line, not just the press, so the matching equipment is sized to the same tonnage.
Power, Footprint And Labor
A YZYX120 sits on about 1860 × 740 mm of floor and weighs around 680 kg; a YZYX140 climbs toward 860 kg and needs 18.5 kW. Check that your plant has the three-phase power (380 V typical) and the floor to stand the machine level. Smaller 6YL presses can run on 7.5–11 kW and are mobile enough for a village oil shop; the larger YZYX130/140 are fixed installations. Also count operators: a single press runs well with one feed operator plus one at the filter, and you will want a small maintenance budget for pressing screws, cages, and choke rings - these are the wear parts that decide real life.
Conclusion
Screw oil press capacity is not a single number on a spec sheet - it is the intersection of model size, seed type, hot or cold preparation, and how hard you squeeze the cake. Use the YZYX/6YL model numbers as a size ladder (70 ≈ 1 t/day, 120 ≈ 6.5 t/day, 130/140 ≈ 8–11 t/day), then ask the supplier to re-quote that capacity on your seed and your residual-oil target. Size the cooker, feeder, and oil filter to the same tonnage, check your three-phase power and floor, and plan for routine screw and cage replacement. Done that way, the press you buy will be the press that actually runs at the capacity you need.







